| Exam Code | 200-105 |
| Exam Name | Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) |
| Questions | 219 Questions Answers With Explanation |
| Update Date | March 05,2024 |
| Price |
Was : |
Are you ready to take your career to the next level with Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)? At Prep4Certs, we're dedicated to helping you achieve your goals by providing high-quality 200-105 Dumps and resources for a wide range of certification exams.
At Prep4Certs, we're committed to your success in the Cisco 200-105 exam. Our comprehensive study materials and resources are designed to equip you with the knowledge and skills needed to ace the exam with confidence:
Start Your Certification Journey Today
Whether you're looking to advance your career, expand your skill set, or pursue new opportunities, Prep4Certs is here to support you on your certification journey. Explore our comprehensive study materials, take your exam preparation to the next level, and unlock new possibilities for professional growth and success.
Ready to achieve your certification goals? Begin your journey with Prep4Certs today!
R1 is configured with the default configuration of OSPF.From the following list of IP addresses configured on R1, which address will the OSPFprocess select as the router ID?
A. 192.168.0.1
B. 172.16.1.1
C. 172.16.2.1
D. 172.16.2.225
What would be the destination Layer 2 address in the frame header for a frame that is being forwarded by Dubai to the host address of 172.30.4.4?
A. 825
B. 230
C. 694
D. 387
OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF?
A. 2
B. 3
C. 4
D. 5
E. 6
F. 7
If required, what password should be configured on the DeepSouth router in the branch office to allow a connection to be established with the MidEast router?
A. No password is required.
B. Enable
C. Secret
D. Telnet
E. Console
To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.)
A. R2(config-if)#clock rate
B. R2(config-if)#bandwidth
C. R2(config-if)#ip ospf cost
D. R2(config-if)#ip ospf priority
E. R2(config-router)#distance ospf
Refer to the exhibit.Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown?
A. One interface has a problem.
B. Two interfaces have problems.
C. The interfaces are functioning correctly.
D. The operational status of the interfaces cannot be determined from the output shown.
A network administrator has configured access list 173 to prevent Telnet and ICMP trafficfrom reaching a server with the address of 192.168.13.26. Which commands can the administrator issue to verify that the access list is working properly? (Choose three.)
A. Router# ping 192.168.13.26
B. Router# debug access-list 173
C. Router# show open ports 192.168.13.26
D. Router# show access-lists
E. Router# show ip interface
Which command can be used from a router to verify the Layer 3 path to a host?
A. tracert address
B. traceroute address
C. telnet address
D. ssh address
After the network has converged, what type of messaging, if any, occurs between R3 and R4?
A. No messages are exchanged.
B. Hellos are sent every 10 seconds.
C. The full database from each router is sent every 30 seconds.
D. The routing table from each router is sent every 60 seconds.
A static map to the S-AMER location is required. Which command should be used to create this map?
A. frame-relay map ip 172.30.0.3 825 broadcast
B. frame-relay map ip 172.30.0.3 230 broadcast
C. frame-relay map ip 172.30.0.3 694 broadcast
D. frame-relay map ip 172.30.0.3 387 broadcast
_Pic_4.PNG)